FREE · PRIVATE · INSTANT

Brick Wall Calculator

Brick Wall Calculator estimates face bricks for straight walls for exterior veneer, garden, and partition wall faces. Enter job dimensions in U.S. customary units, adjust supplier assumptions, and get purchase-ready quantities instantly.

Loading calculator…

HOW IT WORKS

Formula and assumptions

Subtract openings from wall area, divide by the actual unit face plus the mortar joint module, apply waste, and round up.

Unit dimensions are actual face dimensions before the mortar joint is added.
Openings are entered as total square feet.

FIELD CHECK

Before you order

Calculate each wall elevation separately if openings, brick size, pattern, or waste conditions change.

Worked example

Example: with wall length 40 ft, wall height 9 ft, doors and windows 63 sq ft, waste allowance 8 %, the brick wall calculator returns 2,200 bricks for bricks to buy. The supporting check is pallets: 5 pallets. Replace the prefilled measurements and supplier assumptions with the project values before ordering.

PROJECT GUIDE

Using this calculator well

WHEN TO USE IT

Best use of this calculator

Use the result as a planning estimate, then verify field measurements and product-specific data before ordering or building.

INPUTS EXPLAINED

What each input means

Wall length: Enter the measured value and choose the matching unit (ft, in, yd, m, cm).
Wall height: Enter the measured value and choose the matching unit (ft, in, yd, m, cm).
Doors and windows: Enter the project value in sq ft.
Actual unit face length (without joint): Enter the measured value and choose the matching unit (in, ft, cm, mm).
Actual unit face height (without joint): Enter the measured value and choose the matching unit (in, ft, cm, mm).
Mortar joint: Enter the measured value and choose the matching unit (in, ft, cm, mm).
Waste allowance: Enter the project value in %.
Units per pallet: Enter the project value used by the calculation.
Price per unit: Enter the project value in $.

COMMON MISTAKES

Checks that prevent bad estimates

Mixing units or entering a measurement in a different unit than the selected field unit.
Using a planning default when the exact manufacturer or supplier specification is available.
Rounding intermediate measurements too early instead of rounding the final purchase quantity.
Ignoring waste, compaction, cuts, laps, settlement, or full-package rounding where the project requires them.

SOURCES & REVIEW

How this estimate is supported

The implemented formula, assumptions, and worked example on this page are the calculator-specific reference. BuildYard's broader rules are documented in the Calculation Methodology and Sources & References.

For material density, coverage, yield, dimensions, package quantity, price, and other product-specific values, the current manufacturer or supplier specification should override a planning default.

Last reviewed: September 15, 2026, as part of the site-wide calculator workflow validation pass. See the BuildYard Changelog.

LEARN THE METHOD

Guides related to this calculator

All guides

Pavers & hardscape

Paver Quantity, Base, Bedding Sand, and Waste

Learn how paver area, unit size, pallet coverage, base depth, bedding sand, compaction, borders, and cut waste fit into a hardscape material estimate.

Read guide →

COMMON QUESTIONS

Brick Wall Calculator FAQ

What does the Brick Wall Calculator calculate?

It converts the measurements for exterior veneer, garden, and partition wall faces into the buying units normally used for face bricks for straight walls, with the relevant waste, package, weight, or cost outputs shown on the result card.

How accurate is this brick wall calculator?

The geometry is calculated from the values you enter. Final ordering accuracy still depends on field measurements, supplier density or coverage, product dimensions, compaction, cuts, and the selected allowance.

What should I verify for exterior veneer, garden, and partition wall faces?

Calculate each wall elevation separately if openings, brick size, pattern, or waste conditions change. Confirm the selected product, field conditions, and purchasing increments before placing the order.

Should I round the result up?

Yes for indivisible buying units such as bags, sheets, bundles, pallets, boxes, bars, and truck loads. The calculator rounds those purchase quantities up automatically.

KEEP ESTIMATING

Related masonry calculators

All Masonry tools

Masonry