FREE · PRIVATE · INSTANT

Mortar Calculator

Mortar Calculator estimates mortar cement and sand for brick, block, stone, and repair mortar batches. Enter job dimensions in U.S. customary units, adjust supplier assumptions, and get purchase-ready quantities instantly.

Loading calculator…

HOW IT WORKS

Formula and assumptions

Convert wet volume to dry ingredients, divide by the selected cement:sand:aggregate ratio, and round cement bags up.

The ratio is measured by dry volume.
Water, admixtures, entrained air, and batching loss require mix-specific adjustments.

FIELD CHECK

Before you order

For bagged preblended mortar, replace this nominal mix workflow with the yield printed on the product.

Worked example

Example: with pour length 12 ft, pour width 8 ft, pour depth 0.375 in, waste allowance 15 %, the mortar calculator returns 2 bags for cement bags. The supporting check is wet concrete volume: 0.13 cu yd. Replace the prefilled measurements and supplier assumptions with the project values before ordering.

PROJECT GUIDE

Using this calculator well

WHEN TO USE IT

Best use of this calculator

Use the result as a planning estimate, then verify field measurements and product-specific data before ordering or building.

INPUTS EXPLAINED

What each input means

Pour length: Enter the measured value and choose the matching unit (ft, in, yd, m, cm).
Pour width: Enter the measured value and choose the matching unit (ft, in, yd, m, cm).
Pour depth: Enter the measured value and choose the matching unit (in, ft, cm, mm).
Waste allowance: Enter the project value in %.
Cement ratio: Enter the project value used by the calculation.
Sand ratio: Enter the project value used by the calculation.
Aggregate ratio: Enter the project value used by the calculation.
Dry-volume factor: Enter the project value used by the calculation.
Cement volume per bag: Enter the project value in cu ft.
Price per cement bag: Enter the project value in $.

COMMON MISTAKES

Checks that prevent bad estimates

Mixing units or entering a measurement in a different unit than the selected field unit.
Using a planning default when the exact manufacturer or supplier specification is available.
Rounding intermediate measurements too early instead of rounding the final purchase quantity.
Ignoring waste, compaction, cuts, laps, settlement, or full-package rounding where the project requires them.

SOURCES & REVIEW

How this estimate is supported

The implemented formula, assumptions, and worked example on this page are the calculator-specific reference. BuildYard's broader rules are documented in the Calculation Methodology and Sources & References.

For material density, coverage, yield, dimensions, package quantity, price, and other product-specific values, the current manufacturer or supplier specification should override a planning default.

Last reviewed: September 15, 2026, as part of the site-wide calculator workflow validation pass. See the BuildYard Changelog.

LEARN THE METHOD

Guides related to this calculator

All guides

Pavers & hardscape

Paver Quantity, Base, Bedding Sand, and Waste

Learn how paver area, unit size, pallet coverage, base depth, bedding sand, compaction, borders, and cut waste fit into a hardscape material estimate.

Read guide →

COMMON QUESTIONS

Mortar Calculator FAQ

What does the Mortar Calculator calculate?

It converts the measurements for brick, block, stone, and repair mortar batches into the buying units normally used for mortar cement and sand, with the relevant waste, package, weight, or cost outputs shown on the result card.

How accurate is this mortar calculator?

The geometry is calculated from the values you enter. Final ordering accuracy still depends on field measurements, supplier density or coverage, product dimensions, compaction, cuts, and the selected allowance.

What should I verify for brick, block, stone, and repair mortar batches?

For bagged preblended mortar, replace this nominal mix workflow with the yield printed on the product. Confirm the selected product, field conditions, and purchasing increments before placing the order.

Should I round the result up?

Yes for indivisible buying units such as bags, sheets, bundles, pallets, boxes, bars, and truck loads. The calculator rounds those purchase quantities up automatically.

KEEP ESTIMATING

Related masonry calculators

All Masonry tools

Masonry